Дугуй хөрөөний ирийг хэрхэн сонгох вэ?
мэдээллийн төв

Дугуй хөрөөний ирийг хэрхэн сонгох вэ?

Дугуй хөрөөний ирийг хэрхэн сонгох вэ?

Дугуй хөрөө нь олон төрлийн DIY төслүүдэд таны хамгийн том холбоотон байх болно. Гэхдээ өндөр чанартай иртэй бол эдгээр хэрэгслүүд нь үнэ цэнэтэй зүйл биш юм.


Өргөтгөх нүхийг хөрөөний ирэнд суулгасан тул метал нь халах үед өргөжиж болно гэдгийг анхаарна уу. Зарим лого, товчлол нь тухайн брэнд эсвэл үйлдвэрлэгчийн онцлогтой байж болно.

Circular saw blades are toothed metal discs featuring a hole in the centre called a bore. This hole is used to secure the blade to the saw. Essentially, the bore size must match the size of your saw but you can select a blade with a larger bore provided that you use a reducer ring or bush to attach it to the saw. Аюулгүй байдлын тодорхой шалтгааны улмаас цооногийн диаметр нь ирийг цооногийн голд бэхлэх самарнаас 5 мм-ээс багагүй байх ёстой.

The diameter of the blade must not exceed the maximum size accepted by your circular saw; Энэ мэдээллийг бүтээгдэхүүний техникийн үзүүлэлтэд тусгасан болно. Buying a blade that is slightly smaller is not dangerous but it will reduce cutting depth. Хэрэв та итгэлгүй байгаа бол үйлдвэрлэгчийн зааврыг харна уу эсвэл хөрөө дээрээ байгаа хутганы хэмжээг шалгана уу.

A saw blade consists of a series of teeth that perform the cutting action. Teeth are set out all around the circumference of a circular saw blade. The number of teeth varies depending on numerous factors, including application, so you'll have to determine whether you'll be using the blade for ripping or crosscutting.This is the part of the blade that is responsible for making cuts. Шүд бүрийн хоорондох зайг залгиур гэж нэрлэдэг. Илүү том хоолой нь модны үртэсийг илүү хурдан гадагшлуулах боломжийг олгодог. Иймээс том шүдтэй ир нь хоорондоо зайтай байх нь урагдаж зүсэхэд (өөрөөр хэлбэл тариагаар зүсэхэд) тохиромжтой.

It is important to note that the gullet size can actually be more important than the number of teeth featured. 24 шүдтэй 130 мм-ийн ир нь 48 шүдтэй 260 мм-ийн иртэй ижил хоолойтой байна. If it's all sounding a bit complicated, don't worry – blades are usually marked to indicate the type of job they are equipped to handle whether this be coarse work, finishing work or a range of tasks.

Non-geared electric motors typically run at 1,725 RPM or 3,450 RPM. Ихэнх цахилгаан хэрэгсэл нь шууд хөтлөгчтэй байдаг тул ир нь моторын босоо ам руу шууд холбогддог. In the case of these direct drive tools, such as handheld circular saws (not worm driven), table saws and radial arm saws, this will be the RPM which the blade is operating at. Гэсэн хэдий ч зарим дугуй хөрөө байдаг бөгөөд тэдгээр нь шууд хөтлөгддөггүй бөгөөд өөр өөр хурдтай ажилладаг. Worm drive handheld circular saws typically run between 4,000 and 5,000 RPM. Belt driven table saws can also run over 4,000 RPM.

Хэдийгээр хөрөө болон ир нь RPM-ээр үнэлэгддэг боловч материалыг огтлох нь тийм биш юм. Зүсэх төрөл, урах эсвэл огтлох нь бас өөр түүх юм. Учир нь хөрөөний эргэлт нь түүний зүсэлтийн хурдыг сайн харуулж чаддаггүй. If you take two saws, one which has a 7-1/4” blade and the other which has a 10” blade, and run them at the same speed, as measured in RPM, they won't cut at the same speed. That's because even though the center of both blades is moving at the same speed, the outer edge of the larger blade is moving faster than the outer edge of the smaller blade.

  • 1.Check the features of your saw. Хөрөөний диаметр, нүхний хэмжээг мэдсэний дараа та өөрийн хэрэгцээнд нийцүүлэн ир сонгох хэрэгтэй.

Таны зүсэх ажилд аль хөрөөний ир тохирох вэ гэсэн асуулт танд байсаар байна уу? The experts atБААТАР


Шуудангийн цаг: 2024 оны 6-р сарын 06

Бидэнд мессежээ илгээнэ үү:

Энд мессежээ бичээд бидэнд илгээгээрэй.
//